|
|
WISE-7560M - 6-channels Relay, 6-channels DI and 2-port Ethernet Switch by ICP DAS
|
|
|
WISE-7560M_SUMMARY.html
- Runs on browsers, no extra software tool is required.
- No more programming, Web pages provided for control logic editing.
- IF-THEN-ELSE logic rules execution ability.
- Built-in I/O (Relay: 6 Channels; DI: 6 Channels)
- Support I/O Moniitoring/Control, Counter, Timer, Schedule, Email sending and CGI Command sending operations.
- Modbus TCP Protocol for SCADA System Integration.
- IEEE 802.3af-compliant Power over Ethernet (PoE).
- 2-port Ethernet Switch for Daisy-Chain Topology.
- MQTT Protocol for IT & IoT (Internet of Things) System Integration.
|
|
|
WISE-7560M_DESCRIPTION.html
WISE-7560M provides 6 wet contact digital input channels and 6 form A electromechanical relays. It features
optical isolation for 3000 VDC of transient overvoltage protection and doesn't have channel-to-channel isolation. Note:
When inductive loads are connected to the relays, a large counter electromotive force may occur when the relay actuates
because of the energy stored in the load. These flyback voltages can severely damage the relay contacts and greatly
shorten the relay life. Limit these flyback voltages at your inductive load by installing a flyback diode for DC loads
or a metal oxide varistor for AC loads. WISE-7560M follows IEEE 802.3af-compliant Power over Ethernet (PoE)
specification. It allows receiving power from PoE enabled network by Ethernet pairs. In additional to this, WISE-7560M
also has a built-in two-port Ethernet switch to implement daisy-chain topology. The cabling is much easier and total
costs of cable and switch are significantly reduced.
WISE-7560M.html
Hardware Specifications
Channels
|
6
|
Contact
|
Wet Contact
|
Sink/Source (NPN/PNP)
|
Sink/Source
|
On Voltage Level
|
+10 VDC to +50 VDC
|
Off Voltage Level
|
+4 VDC Max.
|
Input Impedance
|
10 kΩ
|
Counters
|
Channels
|
6
|
|
Max. Counts
|
16-bit (65535)
|
|
Max. Input Frequency
|
50 Hz
|
|
Min. Pulse Width
|
10 ms
|
Overvoltage Protection
|
70 VDC
|
Channels
|
6
|
Type
|
Power Relay, Form A (SPST N.O.)
|
Contact Rating
|
5 A @ 250 VAC/24 VDC (Resistive Load)
|
Min. Contact Load
|
10 mA @ 5 V
|
Operate Time
|
10 ms (max.)
|
Release Time
|
5 ms (max.)
|
Mechanical Endurance
|
2 × 107 ops.
|
Electrical Endurance
|
105 ops.
|
Ethernet Port
|
2 x RJ-45, 10/100 Base-TX, Swtich Ports
|
PoE
|
Yes
|
Protocol
|
Modbus TCP, MQTT
|
Ethernet Port
|
2 x RJ-45, 10/100 Base-TX, Swtich Ports
|
PoE
|
Yes
|
for System Running
|
Yes
|
for Ethernet Link/Act
|
Yes
|
for I/O Channel Status
|
Yes
|
for PoE Power
|
Yes
|
ESD (IEC 61000-4-2)
|
±4 kV Contact for Each Terminal and ±8 kV Air for Random Point
|
EFT (IEC 61000-4-4)
|
±2 kV for Power Line
|
Surge (IEC 61000-4-5)
|
±2 kV for Power Line
|
Reverse Polarity Protection
|
Yes
|
Powered from Terminal Block
|
12 ~ 48 VDC
|
Powered from PoE
|
Yes, IEEE 802.3af, Class1
|
Consumption
|
3.8 W (Max.)
|
Dimensions (L x W x H)
|
120mm x 97mm x 42mm
|
Installation
|
Wall mounting
|
Operating Temperature
|
-25 °C to +75 °C
|
Storage Temperature
|
-30 °C to +80 °C
|
Humidity
|
10 to 90% RH, non-condensing
|
Software Specifications
Rule Configuration Website
|
Access Web server on WISE controllers to edit and upload logic rules through web browser.
|
72 IF-THEN-ELSE Logic Rules
|
3 IF conditions with AND or OR operators 3 THEN actions and 3 ELSE actions
|
48 Internal Registers
|
Hold temporary variables and read/write data
|
24 Timers
|
Delay / Timing functions.
|
24 Schedules
|
Setup prescheduled routine tasks.
|
24 Emails
|
Send Email messages to pre-set Email receivers.
|
24 CGI Commands
|
Send pre-set CGI commands.
|
24 Recipes
|
Set up THEN/ELSE action groups.
|
8 P2P remote modules
|
Set up the connection information for the remote WISE modules.
|
Modbus TCP Protocol
|
Real time control and monitoring I/O channels and system status of controllers via SCADA software.
|
MQTT Protocol
|
Real time message publish/subscribe mechanism for I/O channels and system status via IT/IoT software.
|
DI Channel
|
ON, OFF, ON to OFF, OFF to ON, Change
|
Internal Register
|
=, >, <, >=, <= (value)
|
DI Counter DO Counter
|
=, >, <, >=, <= (value), Change
|
Timer
|
Timeout, Not Timeout
|
Schedule
|
In Range, Out of Range
|
P2P
|
DI, AI, DI counter, DO counter, IR
|
Rule Status
|
Enable, Disable
|
DO Channel
|
ON, OFF, Pulse Output
|
Internal Register
|
Change the value
|
DI Counter DO Counter
|
Reset
|
Timer
|
Start, Reset
|
Schedule
|
Enable, Disable
|
Email MQTT message CGI Commands
|
Send
|
Recipe
|
Execute
|
P2P
|
DO(On/Off), AO, IR
|
Rule Status
|
Enable, Disable
|
|
l');
?>
|