|
|
I-7530A-MR - Modbus RTU to CAN converter. Converts Modbus RTU to CANbus Protocol. by ICP DAS
|
|
|
I-7530A-MR_SUMMARY.html
-
RoHS Design
-
Fully compatible with ISO 11898-2 standard
-
Programmable CAN bus baud rate from 10 kbps to 1 Mbps or user-defined baud rate
-
Support CAN bus acceptance filter configuration
-
Support firmware update via RS-232
-
Provide utility tool for module setting and CAN bus communication testing
-
Built-in jumper to select 120O terminator resistor
-
CAN buffer: 128 data frames ; UART buffer: 256 bytes
-
Power, data flow and error indicator for CAN and UART status
-
Hardware Watchdog design
-
Convert CAN message to specific ASCII command string (Normal mode)
-
Convert specific ASCII command string to CAN message (Normal mode)
-
Provide the transparent communication between the RS-232/485/422 devices via CAN bus (Pair-connection mode)
-
Support function code 0x03/0x04/0x10 of Modbus RTU command for reading and writing CAN message (Modbus RTU mode)
|
|
|
I-7530A-MR_DESCRIPTION.html
The I-7530A-MR Modbus RTU to CAN converter is helpful for data exchanging between the RS-232/485/422 devices and the CAN devices. It supports three communication modes: "Normal", "Modbus RTU", "Pair-connection".
I-7530A-MR.html
CAN Interface
|
Controller
|
Microprocessor inside with 96 MHz
|
Transceiver
|
NXP 82C250
|
Connector
|
9-pin male D-Sub (CAN_L, CAN_H, N/A for others)
|
Channels
|
1
|
Baud Rate (bps)
|
10 k, 20 k, 50 k, 100 k, 125 k, 250 k, 500 k, 800 k and 1 M (allow
user-defined baud rate)
|
Protection
|
3000VDCpower protection and 3750Vrms photo-couple isolation on CAN
side
|
Terminator Resistor
|
Selectable 120O terminator resistor by jumper
|
Support Protocol
|
ISO-11898-2, CAN 2.0A and CAN 2.0B
|
Pin Assignment
|
C.I.A. DS-102 (CAN_H=7, CAN_L=2)
|
UART Interface
|
Connector
|
14-pin terminal connector
|
COM
|
RS-232 : TxD, RxD, GND; RS-422 : TxD+, TxD-, RxD+, RxD-; RS-485 :
DATA+, DATA-
|
Baud Rate (bps)
|
300,600,1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400
|
Protection
|
3000VDCpower protection and 2500Vrms photo-couple isolation on UART
side
|
LED
|
Round LED
|
PWR/CAN/UART
|
Power
|
Power supply
|
+10 ~ +30 VDC
|
Power Consumption
|
1.5 W
|
Dip Switch
|
Init (Firmware Update, Module Configuration)/Normal (Firmware
Operation)
|
Mechanism
|
Installation
|
DIN-Rail
|
Dimensions
|
72mm x 118mm x 35mm (W x L x H)
|
Environment
|
Operating Temperature
|
-25 ~ 75 ?
|
Storage Temperature
|
-30 ~ 80 ?
|
Humidity
|
10 ~ 90% RH, non-condensing
|
|
|
|
l');
?>
|