|
|
|
2174/BNC/EUI-2PK - High Speed CopperLink Ethernet Extender Kit (Local and Remote); BNC Line, 100-240VAC
by PATTON
|
|
|
|
- Ethernet Extension—Extend 10/100Base-TX Ethernet up to 10,000 feet (3 kilometers)—well beyond the 328-foot (100-meter) limitation—over a single twisted-pair, Cat 5e/6/7, or even coaxial cable.
- Operates Over Twisted Pair—Realize fiber-optic speeds without the expense—and hassle—of installing new cables or line-of-site wireless circuits.
- Plug and Play—Set these units up straight out of the box. No configuration is required. Auto-sensing 10/100 Ethernet ports support full or half duplex operation.
- Multiple Line Rates Supported—Boasting downstream line rates up to 168 Mbps, the switch-selectable rate mode options optimize rate and reach for the noise environment, wire gauge/type and length.
- Transparent LAN Bridging—Bypass network configuration requirements by transparently passing all higher layer protocols—including 802.1Q VLAN frames (tagged and untagged). Data-transmission mechanism is fully transparent to such IP video compression schemes as MPEG-4, H.264 and MJPEG.
|
|
|
The Patton Model 2174-BNC-EUI-2PK delivers off-the-chart symmetrical line rates greater than 100 Mbps. Best of all—like all CopperLink™ products—the Model 2174 leverages existing copper infrastructure to deliver high speed Ethernet connectivity over voice-grade twisted pair, Cat 5e/6/7, and—new to the CopperLink™ line—coaxial cabling.
Four user-selectable configuration profiles—combined with Patton’s auto-rate adaptation feature—ensure maximum achievable symmetrical or asymmetrical rates for the installed noise environment, wire gauge/type and length.
Symmetrical line-rate settings are ideal for such applications as remote LAN extension, video teleconferencing, and data backhaul. Asymmetrical configurations are well-suited for applications requiring higher downstream speeds and/or longer distances between Ethernet devices. Typical symmetrical scenarios include medical imaging, livestock monitoring, underwater video, internet gaming, and transporting high-resolution IP video from security cameras.
Realize fiber-like speed and distance without the expense of fiber with Patton’s Ultra-High-Speed CopperLink™ Ethernet Extenders.
| CopperLink Line Interface |
• RJ-45 (pin 4 = ring; pin 5 = tip) • BNC 75-ohm coax • Terminal block, 2-position |
| CopperLink Line Modulation |
DMT (Discrete Multi-Tone) |
| Ethernet Interface (x4) |
8-position shielded RJ-45. Auto-sensing 10/100Base-TX with half or full duplex operation. |
| Protocol |
Transparent to high layer protocols: supports 802.1Q VLAN tagged or untagged frames. Transparent to IP Video schemes: fully transparent to such compression schemes as MPEG-4, H.264, and MJPEG. |
| Ethernet Interface (x4) |
8-position shielded RJ-45. Auto-sensing 10/100Base-TX with half or full duplex operation. |
| Impulse Noise Protection Modes |
Selectable fast and interleave modes |
| Target SNR Modes |
6 dB & 9 dB |
| Management |
8-position DIP switch |
| Monitoring |
8 LEDs display Power, Link, Ethernet 1-4, Remote, and Local status. |
| Dimensions |
1.25 H x 6.22 W x 4.75 D in. (31.8 H x 158 W x 120.7 D cm) |
| Power Supply |
External AC: 100–240 VAC |
| Compliance |
FCC Part 15A, CE Mark, EMC Directive 89/336/EEC, Low-Voltage Directive 73/23/EEC |
| Environment |
Temperature: 0 to 50°C
Humidity: 5 to 95%, non-condensing
Extended Temperature: -40 to 85°C (Model CL1214E)
Extended Humidity: Up to 85% condensing (Model CL1214E/CC) |
| Weight |
0.4 lbs (181 g) |
|
|
