Indicators |
Power / TST |
This green LED is turned on when power is applied to the media
converter. Otherwise it is off. The LED will blink when in Loopback test
mode. |
Fiber link on / Receive activity (LKF) |
This green LED is operational only when power is applied. The LED is on
when the 100Base-FX link is on and flashes with a 50% duty cycle when
data is received. |
Copper link on / Receive activity (LKC) |
This green LED is operational only when power is applied. The LED is on
when the 100Base-TX link is on and flashes with a 50% duty cycle when
data is received. |
Switches: On-Board |
Auto-Negotiation (802.3u) |
Enabled (Default) -
The media converter uses 802.3u Auto-negotiation on the 100Base-TX
interface. It is set to advertise full duplex.
Disabled - The media
converter sets the 100Base-TX port to full duplex. |
Pause |
Pause should be enabled when all devices connected to the media
converter support pause. Auto-Negotiation must be Enabled to use this
feature.
Enabled (Default) -
The Media converter will advertise Pause capability during
Auto-Negotiation on the 100Base-TX interface.
Disabled - The Media
converter will advertise that it does not have Pause capability during
Auto-Negotiation on the 100Base-TX interface. |
Link Pass Through |
Enabled (Default) -
When the state of the receiver is changed on the 100Base-TX interface it
is reflected on the 100Base-FX fiber transmitter. When the state of the
receiver on the 100Base-FX interface is changed it is reflected on the
100Base-TX transmitter.
When a Far-End Fault Indication is received on the fiber interface the
100Base-TX transmitter is turned off. When the Far-End Fault Indication
is cleared the transmitter is turned back on.
Disabled - The
100Base-TX and the 100Base-FX fiber interface operate independently.
Far-End Fault indication on the 100Base-FX fiber interface has no effect
on the 100Base-TX interface. |
Far-End Fault (FEF) |
Enabled (Default) -
The media converter transmits the Far-End Fault Indication over the
100Base-FX fiber connection whenever a receive failure is detected on
the 100Base-FX fiber connection. The media converter continuously
monitors the100Base-X fiber connection and clears the Far-End Fault
Indication condition when a valid signal is received.
Disabled - Far-End
Fault Indications are not transmitted regardless of the condition of the
receive signal on the 100Base-FX fiber connection. |
Remote Loopback |
The media converter can perform a loopback on the 100Base-X fiber
interface.
Disabled (Default - Up)
Enabled - The
100Base-X receiver is looped to the 100Base-X transmitter. The
100Base-TX transmitter is taken off the interface. |
Auto-MDIX (Strap) |
If Auto-Negotiation (802.3u) is enabled, the media converter uses the HP
Auto-MDIX method for the 100Base-TX interface. If Auto-Negotiation
(802.3u) is disabled the Media converter will use the RX Energy method
on the 100Base-TX interface to set the port MDI or MDIX whichever is
appropriate.
Enabled (Default) -
Either a straight-through or crossover type cable can be used to connect
the media converter to the device on the other end of the cable.
Disabled - If the
partner device on the other end of the cable does not have the Auto-MDIX
feature a specific cable, either a straight-through or crossover will be
required to ensure that the media convertor's transmitter and the
partner devices transmitter are connected to the others receiver. The
Media Convertor's 100Base-TX port is configured as MDI with this switch
setting. |
Cables |
100Base-TX |
RJ45 connector, 2 pair CAT 5, EIA/TIA 568A/B or better cable |
Magnetic Isolation |
1.5kv |
Fiber Optic Cable |
Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron
Single Mode: 9/125 micron (ITU-T 625) |
Packet Transmission Characteristics |
Bit Error Rate (BER) |
<10 -12 |
Environmental Specifications |
Operating Temperature |
0 C to 50 C (32 F to 122 F) |
Storage Temperature |
minimum range of -25 C to 70 C (-13 F to 158 F) |
Operating Humidity |
5% to 90% non-condensing |
Storage Humidity |
5% to 95% non-condensing |
Operating Altitude |
Up to 3,048 meters (10,000 feet) |
Heat Output
( BTU/HR ) |
6.8 |
Maximum Power Consumption ( Watts ) |
2.0 |
MTBF (Hours)* |
595,000 |
Mechanical - Hot Swapping Card |
Edge Connecter |
32 pin DIN 41612 / IEC 60603-2 Type B/2 Male. Fist make, last break for
ground and power |
Card insertion and removal |
Captive thumb screws enable fast insertion and removal. Can be further
tighten with a screwdriver. |
Product Weight |
Weight |
0.15 kg, 0.33 lbs |
Packaging |
Shipping Weight |
0.33 kg, .73 lbs |
Shipping Dimensions |
203 x 38 x 152 mm, 8 x 1.5 x 6 inches |
Regulatory Approvals |
Emissions |
FCC Part 15 Class A, EN55022 Class A |
CISPR 22 Class A |
EN61000-3-2 |
Immunity |
EN55024 |
Electrical Safety |
UL 60950-1 |
EN60950 |
CE |
Laser Safety |
EN 60825-1:2007 |
Fiber optic transmitters on this device meet Class 1 Laser safety
requirements per IEC-60825 FDA/CDRH standards and comply with
21CFR1040.10 and 21CFR1040.11. |
Environmental |
Reach, RoHS and WEEE Compliant |
Other |
ECCN: 5A991A |
HTSUS Number: 8517.62.0050 |
Perle Limited Lifetime Warranty |