|
|
856-17721 - ** DISCONTINUED ** IE-MINIFIBERLINX-II/LASTGASP TP-TX/FX-MM850-SC by IMC
|
|
|
10/100 MBPS MANAGED OPTICAL DEMARCATION COMPACT CPE DEVICE
- Loopback troubleshooting
- SNMP Manageable
- Power options: AC, DC and 802.3af Power over Ethernet (PoE)
- Bi-directional Bandwidth control
- MTU: Supports over-sized packets up to 1916
- Supports passive 802.3ah OAM (Operation, Administration & Management
|
|
|
The compact IE-MiniFiberLinX-II/Telco/LastGasp is one of the most versatile
fiber optic NID devices available on the market today. It provides
point-to-point fiber optic connections with a unique management tool to monitor
the entire link between two locations. IE-MiniFiberLinX-II/Telco/Last Gasp was
designed to work with -48 VDC power that is compliant with the Bellcore GR-499
specification, supporting the minimum and maximum transient voltages, typically
required by transport equipment used in Telco environments. Additionally, the
product offers Last Gasp, a Trap notification feature that identifies when the
power lines are down or of a possible power supply failure. Other key features
include; carrier grade remote SNMP management, extra tagging using Q-in-Q, and
PoE (Power over Ethernet).
As a copper-to-fiber converter, the IE-MiniFiberLinX-II/Telco/LastGasp supports
multiple fiber types including multimode, single-mode, single-strand fiber (SSF),
and Course Wavelength Division Multiplexing (CWDM) functionality to increase the
capacity of existing fiber. As a remote, CPE device, it can be connected via the
fiber segment to an iMcV-FiberLinX-II Host module to support Host/Remote
management.
Equipped with one 100 Mbps fiber data port, one 10/100 twisted pair port for
data and management, as well as an auxiliary port designed to function as a
serial port (when used with the included adapter), the IE-MiniFiberLinX-II/Telco/LastGasp
also offers multiple powering options: AC power (with included adapter), DC
(through a 4-terminal power block).
General
-
Preserves complete end-to-end fiber connection integrity
-
Bi-directional bandwidth control (per port, per direction, per VLAN)
-
Read/write IEEE 802.1Q VLAN-tags
-
Extra Tagging with Q-in-Q mode (802.1p)
-
Supports passive 802.3ah OAM (Operation, Administration & Management)
-
QoS: IEEE 802.1p-based packet prioritization (2 queues [high/low] with 8
levels of priority)
-
VLAN filtering up to 32 values
-
Layer 2 packet switching, store and forward operation
-
Forwarding rate: 14,881 pps for 10 Mbps; 148,810 pps for 100 Mbps
-
AutoCross for MDI/MDIX
-
Features Auto Negotiation and Selective Advertising
-
Supports Half and Full-Duplex operation
-
MTU: Supports over-sized packets up to 1916 bytes per packet
Security
-
Password Control
-
Multiple Access Levels: User Assigned Accounts & Access Levels
Management
-
SNMP V1 and V2c compatible
-
Includes GUI-based iView² software for remote management and upgrades
-
Monitors far-end (remote) status without a physical presence or separate
connection
-
IEEE 802.3x Flow Control
-
Includes DHCP and TFTP clients
-
Supports Telnet
-
Includes loopback test modes (MAC swap)
-
Includes LinkLoss and FiberAlert
-
Remote capabilities with built-in support for UMA (IP-less management)
-
RS-232 (Craft) interface for local management
-
Serial cable for direct connection to a PC’s Serial Port
Ethernet Protocols Supported
-
EEE 802.3i 10Base-T twisted pair
-
IEEE 802.3u 100Base-TX twisted pair
-
IEEE 802.3u 100Base-FX or SX fiber
Mechanical
-
Dimensions 0.83”H x 1.80”W x 3.35”D (2.11 x 4.57 x 8.51 cm)
Power
-
AC Wall Adapter: 100 to 240 VAC ±10% input, 5 VDC output, 2A max.
-
DC Input Voltage: 12 to 48 VDC *, 1 to .02A, 7 to 50 VDC, 1 to 0.1A
Environmental
-
Operating Temperature
+14° to +122° F (-10° to +50° C) AC Adapter
-13° to +167° F (-25° to +75° C) DC Adapter
-49° to +185° F (-45° to +85° C) DC Telco
-
Storage Temperature -49° to +185° F (-45° to +85° C)
-
Operating Humidity 5 to 95% Non-condensing
Regulatory Aprovals
-
FCC Class A
-
UL/cUL, CE, CSA, CB
|
|