|
|
|
ioLogik E2240-T - Active Ethernet I/O Server, 8AI/2AO
by MOXA
|
|
|
|
- Active communication with patented Active OPC Server
- Smart Alarm management with email, SNMP Trap, TCP, UDP
- Supports SNMPv1/v2c/v3 protocol
- Save time and wiring costs with peer-to-peer communication
- Front-end intelligent with patented Click&Go control logic, up to 24 rules
- Friendly configuration with web browser
|
|
|
Introduction
Moxa’s ioLogik E2200 is a new type of Ethernet micro RTU controller, which is a PC-based data acquisition and control device that uses proactive, event-based reporting to control I/O devices. Unlike traditional RTUs, which are passive and must poll for data, Moxa’s ioLogik E2200 series with Active OPC Server makes seamless connection with SCADA systems a reality. In addition, SNMP is used for communicating with an NMS (Network Management System) for IT field users. The I/O status of an Ethernet micro RTU controller can be reported and controlled automatically on-site based on user specified conditions. This report-by-exception approach, which is new to PC-based monitoring, requires far less bandwidth than traditional polling methods.
.jpg)
Active Alarming with Local Intelligence
The ioLogik E2200 Micro RTU supports simple and powerful Click&Go™ technology to deliver event-driven reports and allow alarm messages to be sent by email, TCP/UDP, and SMNP Trap with real-time stamps. With built-in Click&Go™ intelligence, the ioLogik E2200 micro RTU can be used for simple output control when it is triggered by input status, without the need for a PC controller. The ioLogik E2200 micro RTU reports I/O status automatically based on user-specified conditions. This report by-exception approach requires far less bandwidth than the traditional polling approach.
.jpg)
| ioLogik E2240 Specifications |
| • Inputs and Outputs |
| Analog Inputs |
8 channels |
| Analog Outputs |
2 channels |
| • Analog Input |
| Type |
Differential input |
| Resolution |
16 bits |
| I/O Mode |
Voltage / Current |
| Input Range |
±150 mV, ±500 mV, ±5 V, ±10 V, 0 to 20 mA, 4 to 20 mA |
| Accuracy |
±0.1% FSR @ 25°C
±0.3% FSR @ -10 and 60°C
±0.5% FSR @ -40 and 75°C |
| Sampling Rate |
All channels:
• 10 samples/sec for voltage
• 6 samples/sec for current
Per channel:
• 1.25 samples/sec for voltage
• 0.75 samples/sec for current
Single channel:
• 1.25 samples/sec for voltage
• 0.75 samples/sec for current |
| Input Impedance |
900k ohms (min.) |
| Built-in Resistor for Current Input |
120 ohms |
| Isolation |
3k VDC or 2k Vrms |
| • Analog Output |
| Resolution |
12 bits |
| Output Range |
0 to 10 V, 4 to 20 mA |
| Drive Voltage |
15 VDC for current output |
| Accuracy |
±0.1% FSR @ 25°C,
±0.3% FSR @ -10 and 60°C
±0.5% FSR @ -40 and 75°C |
| Load Resistor |
Less than 250 ohms |
| • Power Requirements |
| Power Consumption |
198 mA @ 24 VDC |
| • MTBF (mean time between failures) |
| Time |
155,941 hrs |
| Database |
Telcordia (Bellcore) |
| Common Specifications |
| • LAN |
| Ethernet |
1 10/100 Mbps RJ45 port |
| Protection |
1.5 kV magnetic isolation |
| Protocols |
Modbus/TCP, TCP/IP, UDP, DHCP, BOOTP, SNMP, HTTP, CGI, SNTP, SMTP |
| • Serial Communication |
| Interface |
RS-485-2w: Data+, Data-, GND (3-contact terminal block) |
| Serial Line Protection |
15 kV ESD for all signals |
| • Serial Communication Parameters |
| Parity |
None |
| Data Bits |
8 |
| Stop Bits |
1 |
| Flow Control |
None |
| Baudrate |
1200 to 115200 bps |
| Protocol |
Modbus/RTU |
| • Power Requirements |
| Power Input |
24 VDC nominal, 12 to 36 VDC |
| • Physical Characteristics |
| Wiring |
I/O cable max. 14 AWG |
| Dimensions |
115 x 79 x 45.6 mm (4.53 x 3.11 x 1.80 in) |
| Weight |
under 250 g |
| Mounting |
DIN rail or wall |
| • Environmental Limits |
| Operating Temperature |
Standard Models: -10 to 60°C (14 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F) |
| Storage Temperature |
-40 to 85°C (-40 to 185°F) |
| Ambient Relative Humidity |
5 to 95% (non-condensing) |
| Altitude |
Up to 2000 m |
| Note |
Please contact Moxa if you require products guaranteed to function properly at higher altitudes. |
| • Standards and Certifications |
| Safety |
UL 508 |
| EMI |
EN 61000-3-2; EN 61000-3-3; EN 61000-6-4;
FCC Part 15, Subpart B, Class A |
| EMS |
EN 61000-4-2, EN 61000-4-3, EN 61000-4-4,
EN 61000-4-5, EN 61000-4-6, EN 61000-4-8,
EN 61000-4-11, EN 61000-6-2 |
| Shock |
IEC 60068-2-27 |
| Freefall |
IEC 60068-2-32 |
| Vibration |
IEC 60068-2-6 |
| Green Product |
RoHS, CRoHS, WEEE |
| Note |
Please check Moxa’s website for the most up-to-date certification status. |
|
|
|
|
