Need assistance or guidance?

Contact us @: 1-800-301-9097 		Login / Register Contact Us
CART
SHOP BY CATEGORY
SHOP BY BRAND

                         

 
Home Media Converters Ethernet Extender Poe Ethernet Extenders
06004584 eXP-1S110E-RJ - Fast Ethernet Stand-Alone PoE Ethernet Extender - 1 port 10/100Base-TX (RJ-45) . RJ45 Interlink ( VDSL2 by PERLE

06004584 eXP-1S110E-RJ - Fast Ethernet Stand-Alone PoE Ethernet Extender - 1 port 10/100Base-TX (RJ-45) . RJ45 Interlink ( VDSL2
by PERLE
Write a review Write a review
06004584 eXP-1S110E-RJ - Fast Ethernet Stand-Alone PoE Ethernet Extender - 1 port 10/100Base-TX (RJ-45) . RJ45 Interlink ( VDSL2 ) connector. Provides power over Ethernet as a PSE. 48V 65W adapter included - USA Power Cord
Mfg SKU # : 06004584
List Price : $905.00
Our Price : $770.00
Stock : Call for Availability
Quantity :

Perle eXP-S110 PoE Fast Ethernet Extenders transparently extend Ethernet beyond the general IEEE 802.3af limits of 328ft / 100m while providing Power over Ethernet ( PoE ) to standards-based compliant devices such as IP cameras, VoIP phones and wireless access points.

This technology enables users to transparently extend up to four 10/100 Power over Ethernet connections across copper wiring. Use single twisted pair ( CAT5/6/7 ), coax or any existing copper wiring previously used in alarm circuits, E1/T1 circuits, RS-232, RS-422, RS-485, CCTV and CATV applications.

At the central site, the 10/100 Ethernet Extender has full PoE support and operates as a Powered Device (PD) under IEEE 802.3af supporting end-span and mid-span power sources (PSE). Alternatively, the unit can be powered by the included 48v adapter. The PoE Ethernet Extender at the central site then transmits power over the copper wire to power the remote PoE Ethernet Extender and attached PD. The remote PoE Ethernet Extenders are classified as Power Sourcing Equipment (PSE). While using standard UTP cables that carry Ethernet data, Perle eXP-S110 PoE Ethernet Extenders provide up to 15.4 watts of power to Powered Devices (PDs). For longer distance applications the remote PoE Extender (CPE) can be powered by a local 48v adapter. Learn more about PoE.

These simple and effective point to point Ethernet Copper Extenders are perfect for commercial buildings, residential units, hospitality environments, and connecting a remote office or private-network backbone to a corporate LAN … anywhere you need 10/100 Ethernet communication links for PoE devices up to 10,000ft (3KM) in distance.

Perle’s advanced features such as Link Pass-Through* and Interlink Fault Feedback*, Loopback and remote PD reset*, enable Network administrators to “see everything” for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make Perle Ethernet Extenders the smart choice for IT professionals. eXP-S110 PoE Fast Ethernet Extenders are also available with support for Extended Temperature Environments.

eXP-S110 PoE Fast Ethernet Extender Features

Extend Ethernet over twisted pair Extend an Ethernet link over category 5e, 6 and 7 cabling up to 10,000 feet ( 3 km )
Extend Ethernet over Coaxial cable Extend an Ethernet link over 75 ohm coaxial cable
On-board PoE Power Controller As a fully compliant IEEE 802.3af PSE end-span device, this Ethernet Extender’s PoE power controller provides compliant power provisioning and monitoring, properly sensing through signature detection whether or not the attach Ethernet devices are PoE capable or not. This provides a safe connection for both PoE and Non-PoE capable devices.

Competitive PoE Ethernet Extender products operate as a simple passive power injector and will always apply power to RJ45 port pins which may result in damage if non-PoE compliant Ethernet devices are accidently attached.

Click here for more details
Advanced Power capabilities
  • ALT A/B and legacy PoE RJ45 pin selection
  • Current limiting protection
  • Remote PD reset
Fully compliant 802.3af POE PSE
  • Enable/Disable PSE power
  • PD signature detection
  • Over-Current Protection
  • PD power classification detection ( Class 0,1,2,3)
Fully Compliant 802.3af/at PoE PD Only PoE Ethernet Extender solution that provides a Class 0 or 4 signature to PSE for proper operation with PSE equipment such as Cisco PoE switches.

Competitive PoE Ethernet extender solutions cannot be powered by Cisco PoE switches as they cannot provide the necessary PoE PD signature required by the switch. Without this, the switch will not supply power at all.
PSE Status Indicator A multi-color LED provided presents the status of the PSE function for easy troubleshooting of power over Ethernet connections
PD Power Reset ( Port 1 ) Ideal for remotely resetting equipment, this configurable function performs a momentary power reset to the attached Powered Device (PD) on Port #1.

Read our PD Reset Tech Note for further details on this feature
Power Multiplier Selection When used with 4-pair cable such as CAT5 on the VDSL Interlink port, an optional internal strap selection on the Ethernet Extender will provide VDSL transmission data on 1 pair and power across the 3 other pairs enabling even greater distances for power transmission to be achieved.
Broadest range of PoE devices supported Support is included for a broad range of PD ( Powered Devices )

  • IEEE 802.3af PoE ( Alternative A and B )
  • Legacy High Capacitance PDs
  • Cisco legacy VoIP phones and Wireless Access Points
Hi-Speed Performance Utilizes second generation VDSL2 technology ( ITU-T Recommendation G.993. ). When operating under “Profile 30a”, Perle Ethernet Extenders can provide an aggregate VDSL line rate capability of up to 200 mbps.

Actual distance and performance may vary depending on the type / gauge and condition of the wire used and if required, the amount of power you require across the VDSL Link
Plug and Play operation Perle Ethernet Extenders will automatically configure your VDSL interlink connection. The CO/CPE peer association will be determined automatically by the Ethernet Extender. No need to set CO / CPE VDSL pairing.

Once a connection is made, both ends will automatically adjust relevant VDSL parameters to optimize the level of bandwidth possible across the copper link.
Link Pass-Through* With Link Pass-Through the state of the 10/100Base-TX Ethernet connection is “passed through” the VDSL link to the 10/100Base-TX Ethernet connection on its remote peer. A managed switch on the remote end can then report the state (link up or link down) to its network management system so that any errors can be detected and recovered early.

Competitive Ethernet extenders without this feature will never detect or report any error conditions.
Interlink Fault Feedback* Similar to the Link Pass-Through feature, a loss of VDSL link will drop the 10/100 Ethernet port on each end until the link recovers.
Auto-Negotiation The Ethernet Extender supports auto negotiation on the 10/100Base-TX interface
Auto-MDIX Auto-MDIX (Automatic Medium-Dependent Interface crossover) detects the signaling on the 10/100 Ethernet RJ45 interface and determines the type of cable connected (straight-through or crossover) and automatically adopts a compatible pinout.
Fixed Speed and Duplex Some Ethernet equipment require a fixed speed and duplex be used or cannot auto-negotiate. By disabling Auto-Negotiation on the Ethernet Extender, a fixed speed of 10 or 100 mbps as well as Full or half Duplex can be configured through DIP switches.
VLAN Transparent to tagged VLAN ( 802.1Q ) packets.
Transparent to IP Video compression protocols Fully transparent to such IP video compression schemes such as MPEG-4, H.264 and MJPEG.
Power Strain Relief strap A strain relief strap is provided to ensure a solid and secure power connection to the Ethernet Extender. Ideal for areas that may be exposed to vibration.
Loopback When enabled, will perform a loopback on the copper VDSL Interlink.
Remote ( Power over Ethernet )
Power eXP-1S110E
Unit Powered by Local power adapter or VDSL  
Provides Power to: Ethernet  
Power adapter connector Barrel or terminal block
Input Voltage Range from adapter 46V to 57  
Input Voltage Range from VDSL (parasitic) 24 to 57  
Universal AC Adapter 48vDC, 60 watts is included when purchased an individual basis. One 48vDC 60 watts adapter is provided in each kit.
Power Connectors 5.5mm x 9.5mm x 2.1mm barrel socket and 2 pin terminal Block
Remote ( Power over Ethernet )
Ethernet eXP-1S110E
10/100Base TX Port(s) 1 port RJ45 Shielded
Auto-MDIX Auto-MDIX enables proper operation with either straight-through or crossover cabling
Distance Distance up to 100 meters ( 328 feet ) as per IEEE 802.3
Maximum Frame Size 1522
Type of PoE device PSE ( PoE ) IEEE 802.3af
PoE PSE Maximum Power (Watts) Refer to the Power Reach Installation Planning Guide
PoE PSE RJ45 Cable Pinout Alternative A ( default ) on all ports
Pins 3,6 Neg, Pins 1,2 Pos

Alternative B: selectable on port #1
Pins 7,8 Neg, Pins 4,5 Pos

Legacy Cisco Pre-Standard: selectable on port #1
Pins 7,8 Pos, Pins 4,5 Neg
Remote ( Power over Ethernet )
VDSL – Interlink eXP-1S110E
Connector Choice of RJ45, BNC or terminal block models for VDSL link connector
  • RJ45 – RING pin 4, TIP pin 5 (TIA 568 A/B)
  • BNC – Coaxial 75 ohm cable with BNC connector
  • Terminal Block – 2 position screw connectors for use with twisted pair telephone, alarm or serial cabling
Copper Cabling Ethernet Extenders must be connected in pairs using unconditioned wire between 19 ( 0.9 mm ) and 26 AWG ( 0.44 mm ). Circuits that run through signal equalization equipment are not permitted.
Power Injection over the Interlink ( VDSL ) – 2-wire N/A
Short Circuit Protection N/A
Reverse Polarity Protection The voltage from the VDSL link requires proper polarity in order to provide power to the remote extender. Reverse polarity protection however will ensure that there is no damage to the extender
Power Multiplier Selection When used with 4-pair cable such as CAT5 on the VDSL Interlink port, an optional internal strap selection on the Ethernet Extender will provide VDSL transmission data on 1 pair and power across the 3 other pairs enabling even greater distances for power transmission to be achieved
VDSL Line Rate/Reach Actual distance and rates experienced will depend on condition and gauge of wire used. This Rate/Reach table applies to 24 AWG ( 0.5 MM ) twisted pair wiring on RJ45 (RJ) and terminal block (TB) models.
High Speed Asymmetric
Reach ( Distance ) VDSL Rate ( Mbps )
feet meters Downstream Upstream
500 152 101 92
1000 305 101 63
1500 457 90 38
2000 610 62 24
2500 762 55 10
3000 914 42 5
3500 1000 35 3
High Speed Symmetric
Reach ( Distance ) VDSL Rate ( Mbps )
feet meters Downstream Upstream
500 152 101 101
1000 305 85 101
1500 457 62 47
2000 610 60 29
2500 762 44 14
3000 914 30 7
3500 1000 29 4
Long Reach Symmetric
Reach ( Distance ) VDSL Rate ( Mbps )
feet meters Downstream Upstream
500 152 53 44
1000 305 53 43
2500 762 39 18
4000 1219 25 4
5500 1676 17 1.9
7000 2134 8 2.3
7500 2286 7 2.2
8000 2438 5 2.2
Long Reach Asymmetric
Reach ( Distance ) VDSL Rate ( Mbps )
feet meters Downstream Upstream
500 152 78 16
1000 305 78 16
2500 762 55 10
4000 1219 31 0.8
5500 1676 20 0.6
7000 2134 11 0.6
7500 2286 10 0.6
8000 2438 8 0.6
This table applies when the power multiplier option is selected
Power Budget The amount of available power at the PoE PD is dependent on the scenario planned.
Refer to the Power Reach Installation Planning Guide
Remote ( Power over Ethernet )
Indicators eXP-1S110E
Power / TST This green LED is turned on when power is applied to the Ethernet Extender. Otherwise it is off. The LED will blink when in Loopback test mode.
CO - Local Ethernet Extender is operating in CO VDSL mode
CPE - remote Ethernet Extender is operating in CPE VDSL mode
ILNK Indicates Link Status and activity on the Interlink (VDSL) port
ETH Indicates link status and activity on Ethernet port(s).
PSE Status This LED will signify the status of the PSE function. Using multi-color and blinking the unit will show the following status for the PSE;

GREEN — Solid: The PSE has successfully detected a compliant PD and is applying power over the UTP (for legacy pin out simply show active power when applied)

YELLOW — Solid: The PSE is not active. This means the PSE has been configured to provide power, but the PD is :

  • Not connected
  • Has not detected a compliant PD and is not applying power
  • PSE has turned off power for Reset function

OFF — PSE function switch disabled

RED — Blinking: Error Conditions

  • Capacitance too High — 1 blink
  • Resistance too Low or short circuit — 2 blinks
  • Resistance too high or open circuit — 3 blinks
Remote ( Power over Ethernet )
Switches eXP-1S110E
Access Switch settings are accessible through a side opening in the chassis
Rate/Reach Two switches enable the user to select the right balance between speed and distance for their environment.
Signal to Noise Ratio Selectable Signal to Noise Ratio (SNR) of 6dB or 9dB. The higher SNR number provides better impulse noise protection but lowers performance.
Auto-Negotiation (802.3u) control on Port 1 Enabled (Default) - The Ethernet Extender uses 802.3u Auto-negotiation on the 10/100Base-TX interface. It is set to advertise full duplex.

Disabled - The Ethernet Extender sets the port according to the position of the speed and duplex switches.
Force Ethernet Speed on Port 1 When Auto-Negotiation switch is disabled, a fixed speed can be forced on port 1 to 100 (Default) or 10
Force Ethernet Duplex on Port 1 When Auto-Negotiation switch is disabled, Full or half Duplex can be forced on port 1 to Full (Default) or Half
Link Mode Standard (Default) – The 10/100Base-TX link remains active independent of the state of the Ethernet link on its remote peer.

Link Pass-Through- state of the 10/100Base-TX Ethernet connection is “passed through” or propagated across the VDSL link to the 10/100Base-TX Ethernet link on its remote Ethernet Extender peer.
Interlink Fault Feedback Enabled – A loss of VDSL link will drop the 10/100 Ethernet port on each end until the link recovers

Disabled ( Default ) - The state of the VDSL link is not propagated to the 10/100Base-TX port
Loopback Enabled – The VDSL interlink will perform a loopback function, retransmitting all received Ethernet frames back to its remote peer.

Disabled (Default - Up)
PoE PD Class selection N/A
PD Reset ( Port 1 ) When enabled ( down ), the Ethernet Extender will upon loss of link on the VDSL Interlink port, turn off PSE output power to the PD device for 2 seconds then turn the power back on. The power remains on until the VDSL link transitions from up to down again.

When PD Power Reset is disabled ( default ), loss of VDSL link has no effect on power supplied to the PD.
Environmental Specifications eXP-1S110E
Operating Temperature 0 C to 50 C (32 F to 122 F)
Storage Temperature minimum range of -25 C to 70 C (-13 F to 158 F)
Operating Humidity 5% to 90% non-condensing
Storage Humidity 5% to 95% non-condensing
Operating Altitude Up to 3,048 meters (10,000 feet)
Current mA 108 @ 48vdc
Unit Power Consumption watts 5.2
Heat Output
( BTU/HR )		 17.74
MTBF with power adapter (Hours)** 185,061
MTBF without power adapter (Hours)** 300,472
Mounting eXP-1S110E
Wall/Desk Standard
Din Rail Kit Optional
Rack Mount Kit Optional
Product Weight and Dimensions eXP-1S110E
Weight 0.58 Kg, 1.3 lbs
Dimensions 163 x 116 x 37 mm, 6.4 x 4.6 x 1.46 inches
Packaging eXP-1S110E
Shipping Weight 1.27 Kg, 2.8 lbs
Shipping Dimensions 20 x 30 x 7 cm, 7.9 x 11.8 x 2.8 inches
Regulatory Approvals eXP-1S110E
Emissions EN 55022
CISPR 22
IEC/EN 61000-3-2
IEC/EN 61000-3-3
Immunity EN 55024:2010
CISPR 24:2010
IEC/EN 61000-4-2
IEC/EN 61000-4-3
IEC/EN 61000-4-4
IEC/EN 61000-4-5
IEC/EN 61000-4-6
IEC/EN 61000-4-8
IEC/EN 61000-4-11
Electrical Safety EN60950-1
IEC 60950-1
UL 60950-1
CSA C22.2 No. 60950-1
Environmental Reach, RoHS and WEEE Compliant
Other ECCN: 5A991A
HTSUS Number: 8517.62.0050
Perle Lifetime warranty

QUICK LINKS
COMPANY INFO
Payment Types & Security
Copyright © 2024 iComTech. All rights reserved. Shopping Cart Software powered by ecMidas.